Duerkopp Adler N291 Manuale delle Istruzioni

CONTROL DA82GA3312 with control panel V810/V820 INSTRUCTION MANUAL No. 402275 English

EFKA DA82GA3312 10 New parameter value is displayed !  Next parameter is displayed !  or Exit programming !  These val

EFKA DA82GA3312 11 If CODE number is incorrect, repeat input !  If CODE number is correct, the first PARAMETER number at

EFKA DA82GA3312 12 3.4 Program Identification Function Parameter Program number, modification index and identification number display 179 Disp

EFKA DA82GA3312 13 3.6 Keys for Background Information (HIT) with V820 (key assignment see figure on the last page) For fast operator inform

EFKA DA82GA3312 14 Press key E !  Press key E several times until the letter symbol –F– appears !  (ornamental backtack On

EFKA DA82GA3312 15 3.7 Programming of Seams Um häufig vorkommende Nähabläufe komfortabel einstellen und abrufen bzw. verschiedene Nähte mit unter

EFKA DA82GA3312 16 3.7.1 Programming Mode  Each seam pattern is programmed and stored separately.  Exit the teach-in mode after pattern input.

EFKA DA82GA3312 17 Changing the number of compensating stitches If stitch counting and light barrier are to be On at the same time, the num

EFKA DA82GA3312 18 ↓↓↓↓ Righthand arrow above key 1 blinks. 8 Number of stitches for the start backtack  section fo

EFKA DA82GA3312 19 3.7.6 Maximum Number of Seams Exceeded If by inputting a program the total number of 40 seams is exceeded, the teach-in mode c

EFKA DA82GA3312 20 Parameter 275 = 1 Seam suppression enabled: i. e. if the light barrier is Off and stitch counting is set at 0 stitches, the progr

EFKA DA82GA3312 21 4 Putting into Service Before putting the control into service, the following must be ensured, checked and/or adjusted:  T

EFKA DA82GA3312 22 5.2.1 Emergency Run Function If Machine Select Is Invalid If the control cannot identify an admissible value for the machine se

EFKA DA82GA3312 23 Unless the reference position has been stored,  an error message will appear on the display. Turn handwheel several ti

EFKA DA82GA3312 24 Press key E. Parameter value of position 3  appears on the display! Without function! Press key E. Parameter va

EFKA DA82GA3312 25 Note When setting the positions by turning the handwheel, make sure that the displayed numerical value changes. The setting valu

EFKA DA82GA3312 26 5.8 Braking Characteristics Functions Parameter Braking effect when varying the preset value ≤ 4 stages (br1) 207 Braking eff

EFKA DA82GA3312 27 6 Functions and Settings 6.1 First Stitch after Power On Functions Parameter 1 stitch at positioning speed after power O

EFKA DA82GA3312 28 Functions Parameter Switch-on delay with pedal in position –1 (half heelback) (t2) 201 Start delay after disabling the sewing

EFKA DA82GA3312 29 The sewing foot pressure consists of a basic value generated by spring power and a value generated pneumatically. After power On

EFKA DA82GA3312 3 CONTENTS Page 1 Range of Applications 6 1.1 Use in Accordance with Regulations 6 2 Scope of Supply 6 2.1 Special Accessories

EFKA DA82GA3312 30 The number of start backtacking stitches can be set using the above parameters directly on the V810/V820 control panel. For fast

EFKA DA82GA3312 31 6.6.2 End Backtacking Stitch Count Functions Parameter Number of stitches backward (Err) 002 Number of stitches forward

EFKA DA82GA3312 32 Functions Parameter Switch-on delay for the stitch regulator during start backtack (t15) 101 Switch-off delay for the stitch r

EFKA DA82GA3312 33 6.10 Multiple Backtacking Functions Parameter Repetitions of double start backtacking (wAR) 090 Repetitions of double end b

EFKA DA82GA3312 34 Intermediate ornamental backtack: By pressing the key in the seam, the drive stops and the backtack solenoid is activated. The spe

EFKA DA82GA3312 35 6.15 Reverse Motor Rotation Functions Parameter Positioning speed (n1) 110 Number of increments in reverse motor rotation

EFKA DA82GA3312 36 6.16.1 Machine Start Blockage (Blockage 1 and 2) If the input “machine run blockage“ is activated at machine standstill, the run

EFKA DA82GA3312 37 6.17 Thread Monitor Functions Parameter Number of thread monitor stitches (cFw) 085 Thread monitor mode (rFw) 195 If the

EFKA DA82GA3312 38 6.17.5 Parameter 195 = 3 – Model 767, N291 / With Stop / Sewing Foot Down after Seam End Functions as with parameter 195 = 2, but

EFKA DA82GA3312 39 6.19.1 Manual High Lift for Walking Foot – Speed Limitation The high lift during sewing can be set on a handwheel intended for

EFKA DA82GA3312 4 CONTENTS Page 6 Functions and Settings 27 6.1 First Stitch after Power On 27 6.2 Softstart 27 6.2.1 Softstart Speed 27 6.2.2

EFKA DA82GA3312 40 The speed is limited to 2000 RPM or 3000 RPM using the control inputs on A/9 (DB2000) and A/10 (DB3000). The speed limitations can

EFKA DA82GA3312 41 6.20.4 Jumper S1 The jumper S1 located at the top right of the printed circuit board next to the 37-contact socket has the foll

EFKA DA82GA3312 42  Press key E. New value 17 (lower break point)  is entered.  Press key P once. Display of the actual parameter  number.

EFKA DA82GA3312 43 The roller is lifted by enabling the solenoid valve on output A/15. After power On, output A/15 and the correspondiing LED on D/

EFKA DA82GA3312 44 6.24 Thread Trimming Operation Functions Parameter V820 Thread trimmer On lefthand arrow On Key 5 Thread trimmer and thread

EFKA DA82GA3312 45 6.24.4 2nd Thread Tension Release (FSPL2) Functions Parameter Function of output B5/6 “motor running” (mmL) 198 = 1 Functio

EFKA DA82GA3312 46  Parameter 197 = 0 Coupling thread tension reduction with high lift for walking foot and speedomat Off.  Parameter 197 = 1

EFKA DA82GA3312 47 Speed control for the free seam and the seam with stitch counting can be selected using the speed mode. Parameter 142 = 0 Exec

EFKA DA82GA3312 48 6.27.3 Reflection Light Barrier LSM001A Sensitivity setting: Set minimum sensitivity depending on the distance between light bar

EFKA DA82GA3312 49 Parameter 140/144 = 1: Needle up When the key is pressed, the drive runs from position 1 to the reverse position. This does not

EFKA DA82GA3312 5 CONTENTS Page 6.21 Switch Stitch Length 42 6.22 Roller 42 6.23 Thread Clamp 43 6.24 Thread Trimming Operation 44 6.24.1 Thr

EFKA DA82GA3312 50 6.30 Signal Output Position 2  Transistor output with open collector  Signal whenever the needle is in the slot between posi

EFKA DA82GA3312 51 Functions Parameter Speed stage graduation (nSt) 119 The pedal characteristics (speed change from stage to stage) can be var

EFKA DA82GA3312 52 7 Input and Output Function Test Functions Parameter Input and output test (Sr4) 173 Function test of external inputs and t

EFKA DA82GA3312 53 8 Error Displays General Information On the V810 On the V820 Signification InF A1 InF A1 Pedal not in neutral position, whe

EFKA DA82GA3312 54 9 Operating Elements of the V810 Control Panel P+A1 2 3 4variocontrol 810KL2185B-1E The V810 control panel is supplied with sli

EFKA DA82GA3312 55 10 Operating Elements of the V820 Control Panel variocontrol 820P EKL218641 2 3BR85 6 7 9 0A+-F1 The V820 control panel is s

FRANKL & KIRCHNER GMBH & CO KG SCHEFFELSTRASSE 73 – 68723 SCHWETZINGEN – GERMANY PHONE: +49-6202-20

EFKA DA82GA3312 6 1 Range of Applications The drive is suitable for lockstitch, machines: Brand Series DÜRKOPP ADLER N291, 069, 204, 205, 221, 26

EFKA DA82GA3312 7 2.1 Special Accessories Control panel Variocontrol V810 - part no. 5970153 Control panel Variocontrol V820 - part no. 5970154 R

EFKA DA82GA3312 8 3 Operation 3.1 Access Authorization upon Command Input In order to prevent unintentional changes of preset functions the comm

EFKA DA82GA3312 9 3.2 V810 Control Panel Operation 3.2.1 Code Number Input on the V810 Control Panel Example: Technician level CODE number